USG-1 USB TO NMEA
The USG-1 is no longer in production. Opt for the USG-2 instead.
Connect your boat’s data network to your PC with the safety of full electrical isolation.
The Actisense USG-1 is the safest way to connect a boat’s data network to an on-board PC. It converts a USB port into a bi-directional serial port suitable for connecting to a marine standard NMEA 0183 data bus.
5 year guarantee
across entire Actisense range as standard
The ISO-Drive output and OPTO input provide full isolation, making installation simple and free from ground loops.
The OPTO input uses the Actisense isolation circuitry to protect any connected equipment from most common system faults. The isolator can receive very low level differential signals that are often too small to be received by a PC serial port.
The USG overcomes all the problems of using a low-cost USB to RS232 cable from a computer store (when handshaking is not required). It eliminates the risk of damage to the PC as it provides complete isolation.
- Create a serial port connection to an NMEA 0183 system, that may be on a different power circuit from the PC
- Connect two PCs together that are on different power circuits
- Provide a compliant NMEA 0183 port from a USB port
- Receive low level differential signals that are too small to be received by a PC serial port
- Free up PC serial/COM port for other uses
| Supply voltage | From USB port | 4.75 | 5.25 | V |
| Supply current (drawn from USB port)
|
Supply voltage 5v (no load)
Supply voltage 5v (output shorted)
|
40
75
|
46
80
|
mA
mA
|
| Opto-isloated in | NMEA 0183 version 1-3 & PC Serial | |||
| Input voltage tolerance | Continuous operation
Short term operation (< 1 sec) |
-15
-35 |
+15
+35 |
V
V |
| Differential input voltage | Required level for data to be detected | 1.8 | 2.0 | V |
| Input current | 20 | 9.0 | mA | |
| Galvanic isolation | Between input & output | – | 2500 | V |
| Overdrive protection
|
|
–
|
40
|
V
|
| ISO-DRIVE Flexible out | NMEA 0183 version 1-3 & PC Serial | |||
| Differential output voltage | Continuous operation
Max. 100 ohm load |
-5.2
2.1 |
+5.2
– |
V
V |
| Output current (Max) | Max. 100 ohm load | – | 21 | mA |
| Output current (Short) | Due to short circuit protection | 50 | 55 | mA |
| Galvanic isolation | Between Opto-input and (USB ground) | – | 1500 | V |
| Static discharge protected
|
|
–
|
15000
|
V
|
| PC Comm settings | ||||
| Baud rate
|
Set in PC software Comm port settings
|
300
|
115200
|
bps
|
| General | ||||
| Ambient temperature | -20 | +70 | °C | |
| Guarantee | Actisense guarantee | – | 3 | Years |
The ISO-Drive output and OPTO input provide full isolation, making installation simple and free from ground loops.
The OPTO input uses the Actisense isolation circuitry to protect any connected equipment from most common system faults. The isolator can receive very low level differential signals that are often too small to be received by a PC serial port.
The USG overcomes all the problems of using a low-cost USB to RS232 cable from a computer store (when handshaking is not required). It eliminates the risk of damage to the PC as it provides complete isolation.
- Create a serial port connection to an NMEA 0183 system, that may be on a different power circuit from the PC
- Connect two PCs together that are on different power circuits
- Provide a compliant NMEA 0183 port from a USB port
- Receive low level differential signals that are too small to be received by a PC serial port
- Free up PC serial/COM port for other uses
| Supply voltage | From USB port | 4.75 | 5.25 | V |
| Supply current (drawn from USB port)
|
Supply voltage 5v (no load)
Supply voltage 5v (output shorted)
|
40
75
|
46
80
|
mA
mA
|
| Opto-isloated in | NMEA 0183 version 1-3 & PC Serial | |||
| Input voltage tolerance | Continuous operation
Short term operation (< 1 sec) |
-15
-35 |
+15
+35 |
V
V |
| Differential input voltage | Required level for data to be detected | 1.8 | 2.0 | V |
| Input current | 20 | 9.0 | mA | |
| Galvanic isolation | Between input & output | – | 2500 | V |
| Overdrive protection
|
|
–
|
40
|
V
|
| ISO-DRIVE Flexible out | NMEA 0183 version 1-3 & PC Serial | |||
| Differential output voltage | Continuous operation
Max. 100 ohm load |
-5.2
2.1 |
+5.2
– |
V
V |
| Output current (Max) | Max. 100 ohm load | – | 21 | mA |
| Output current (Short) | Due to short circuit protection | 50 | 55 | mA |
| Galvanic isolation | Between Opto-input and (USB ground) | – | 1500 | V |
| Static discharge protected
|
|
–
|
15000
|
V
|
| PC Comm settings | ||||
| Baud rate
|
Set in PC software Comm port settings
|
300
|
115200
|
bps
|
| General | ||||
| Ambient temperature | -20 | +70 | °C | |
| Guarantee | Actisense guarantee | – | 3 | Years |
Yes
needs more information
This is the best looking compact N2K tee with power feed. Better than building your own with individual T’s that ends up being over a foot long just to get the same amount of ports.
Thanks for this access,
Regards,
Brice
I like your products, but I’m not sure who your representatives are in Venezuela. We usually purchase them from your distributors in Miami. At Vzla Marine Group, we use them for our facilities and would like to add your products to our sales catalog.
If you are interested, please contact us.
installation manual